 |
Welcome to Clay's Radio Shop Specializing in Motorcycle, Auto, & Truck Communications & Accessories |
 |
||||||||||
| Read our Privacy Policy | ||||||||||||
 |
|
 |
||||||||||
|
||||||||||||
| Firestik high quality CB antenna brackets & mounts |
| Firestik flat surface mounts | ||
 |
(SS124A) This mount is our most popular stainless steel mount for flat surface applications. The bracket itself is about 4" (102mm) long by 1" (25mm) wide. The supplied stainless steel mounting bolt is a hefty 3/8"-24 x 1" long and includes a stainless steel nut and washers. This mount may be used with antennas up to 4' (1.2m) long. | |
 |
(SSF4A) If your looking for a heavy-duty stainless steel flat mount ... look no more. This mount offers numerous mounting options. The bracket is 2" (51mm) wide, 5" (127mm) long and 0.100" (2.5mm) thick stainless steel. The stud mount hole has a full 1" set back in case you want to replace the stud with one of our Dome Mounts | |
 |
(SS134A) This stainless steel mount was specifically designed to mount an antenna on the flat side-view mirror arm supports commonly found on pick-ups. The upper bracket is 4.6" (117mm) long by 1" (25mm) wide. The distance between the stainless steel clamping bolts (supplied) allows the mount to span material up to 1.4" (36mm) wide | |
 |
(SS24A) This bracket is made of heavy-duty stainless steel. It includes mounting hardware. The actual size of the bracket is 2.25" (57mm) wide by 2.9" (74mm) high (4.2" (107mm) with stud). It protrudes outward from the vertical surface 1.9" (48mm). | |
| Firestik AM/FM/CB Antenna Splitter | ||
 |
(AR-1A) The perfect accessory for people who want to use their standard ground plane dependent Firestik CB antenna for CB and AM/FM radio. | |
| Firestik Trunk Lip Mount | ||
 |
(K74) The
trunk lip bracket slides over trunk edge Two set screws are tightened
from the underside to hold the bracket in place. Recommended
for antennas up to 3ft (92cm). Physically, the mount is 2" (50mm)wide
and 2.5" (63mm) deep. It stands 1" (25mm) above the
vehicle surface without the stud mount, which will add of 2.1" (53mm)
when in place. |
|
| Firestik Stake Pocket Mounts | ||
 |
(SS294A) This stainless steel mount locks into any of the stake hole pockets along the edge of a pick-up truck bed. There is no need to drill any holes in the vehicle. Because of the stud mount configuration on this mount, it can only be used on trucks where there is inside access to the stake hole pocket (from side or bottom) for the coaxial cable to be routed to the mount. | |
 |
(SS194) Those square holes in the bed rails of full size pick-up trucks are the prefect location for a "no-holes" antenna mount. The flat upper bracket is 6" (152mm) long. Includes stud mount, stainless steel brackets and hardware, and a gasket to protect the vehicle finish. | |
 |
(SS194A) Those square holes in the bed rails of full size pick-up trucks are the prefect location for a "no-holes" antenna mount. The flat upper bracket is 6" (152mm) long. Includes stud mount, stainless steel brackets and hardware, and a gasket to protect the vehicle finish. | |
| Firestik & Victory Specialty Mounts | ||
 |
(SS184A) The primary use for the SS-184 stainless steel mount is for antenna installation on the new style Dodge Ram and Dakota pick-ups. The bracket has a pre-determined bend and does not interfere with the closing of the hood. The bracket is 2" (51mm) wide by 4.1" (104mm) long. Due to the close quarters, the stud requires crimp-on coaxial connectors. | |
 |
(SSJ4A) This mount was designed around the new Jeep Wranglers body style (97-99). The mount allows the antenna to be mounted on either the left or right side of the vehicle. After the mount is installed, there will not be any visible mounting holes. All mounting hardware (also stainless steel) is hidden under the vehicles hood | |
 |
(VSSQRCS3) Heavy Duty clamp bracket with 180 degree swivel. Will clamp on to a vertical or horizontal bar due to the 180 degree swivel. Stud mount not included. We recommend a K4A stud mount. | |
 |
(139AD) Vise grip antenna mount. Easily mount your antenna anywhere! Valor | |
 |
(VQRC-1) Victory accessories aircraft aluminum quick release mirror mount with a solid brass SO239 stud mount.. | |
| Door Jamb Mount | ||
 |
(SS204A) The bracket and mounting hardware is made of stainless steel. The bracket is 1.5" (38mm) wide and has a 2" (50mm) reach for mounting inside the door jamb. Overall, the mount is 4.2" (105mm) long. In order to compensate for the door jamb angles, the stud bracket will swivel a full 180 degrees, 90 in each direction. | |
| Firestik Hood, Trunk, or Hatchback Mount | ||
 |
(SS274A) This mount was specifically designed for hood, trunk and hatchback applications. All bracket parts are made of stainless steel. It is fully adjustable to compensate for sloping angles such as those common on mini-van hoods and/or hatchback doors | |
| Workman Side Mount | ||
 |
(PSM1) This mount was designed to bolt to the side of your vehicle. Made by Workman. 3" tall x 1.5" wide. Extends out 2" from side of vehicle. For antennas up to 4 feet long. Workman | |
| Antenna Stud Mounts | ||
 |
Standard Duty Stud Mount - steel top, brass bolt. This standard duty stud mount features chrome plating and is designed for 1/2" holes and has 3/8" threads. For use with the PL-259 coax connector. | |
| |
(K4A) Heavy
Duty Stud Mount - Steel top, bottom &
bolt The K-4A should be used whenever a PL-259 terminated coax cable is to be used (K-8A, K-9A, R-8A, R-9A). Like the K-4, this stud is designed for 1/2" (13mm) holes.3/8" thread bolt |
|
 |
(K4) The K-4 stud utilizes ring terminal connectors (supplied)making it compatible with non-PL-259 terminated coaxial cables. In a typical installation, antennas with 0.600" (15mm) of exposed threads can be used without the fear of bottoming out before proper tightening is accomplished. The K-4 can be used in any mount or mounting surface with a 1/2" (13mm) hole | |
 |
(K4R) The design of the Fire Ring coax termination requires the 1.25" mounting bolt that is found in the K-4R stud mount. For use with the (Fire Ring Coaxial Cable) |
|
 |
(M102) Heavy duty stud mount. Made of stainless steel. The top, bottom, and stud bolt are all stainless. Includes an allen wrench. Francis | |
 |
(SM1L) Chrome plated brass 90 degree heavy duty stud mount | |
 |
(Pred stud S0239) Predator stabilizer stud. Heavy Duty stud mount with stainless steel center bolt. Matches the Predator antenna. This stud is an extremely heavy duty stud for large coil antennas such as the Predator or Monkey Made. | |
 |
(Pred stud T) Predator
stabilizer stud. Heavy Duty stud mount with stainless steel center
bolt. Matches the Predator antenna. (Pred stud terminal type) This stud is an extremely heavy duty stud for large coil antennas such as the Predator or Monkey Made. |
|
 |
(bee hive) Heavy duty bee hive mount. For heavy duty applications | |
| Firestik Roof Mounts | ||
 |
(K4ADD) Attractive mounts for trunk and roof applications. Includes two 2 1/2" circular discs (stainless steel top disc), mounting stud and a rubber gasket to protect vehicle finish. The K-4DD model has a low underside profile for confined space installs. Requires a 1/2" hole and flat surface for installation | |
 |
(K4DD) Attractive mounts for trunk and roof applications. Includes two 2 1/2" circular discs (stainless steel top disc), mounting stud and a rubber gasket to protect vehicle finish. The K-4DD model has a low underside profile for confined space installs. Requires a 1/2" hole and flat surface for installation. | |
Page:
1 2 Next
Page»